Sungkyunkwan University · Engineering
Professor Seunghyun Baik's research lab specializes in the development of advanced nanomaterials and functional composites for thermal management, energy conversion, and electronic applications. Key research directions include designing high-performance thermal interface materials with ultrahigh thermal conductivity using carbon nanotubes and metal nanostructures, creating flexible and durable conductive adhesives for wearable electronics, and engineering phase-change materials with enhanced thermal stability and recyclability. The lab also focuses on improving charge transport in optoelectronic devices, such as perovskite solar cells, through strategic integration of carbon nanomaterials and conductive polymers.
Figures are computed from collected data and may differ slightly.
An ultrahigh thermal conductivity (κ = 160 W m(-1) K(-1) ) of thermal interface materials is achieved with a high enhancement factor (96). A small amount (2.3 vol%) of 1D multiwalled carbon nanotubes (MWNTs) with high κ constructs effective phonon transport pathways between microscale silver-flake islands, and a solid phonon transport junction is realized by the coalescence of silver nanoparticles pre-functionalized on the MWNTs.
An adhesive with high conductivity, flexibility, cyclability, oxidation resistance, and good adhesion is developed using microscale silver flakes, multiwalled carbon nanotubes decorated with nanoscale silver particles, and nitrile butadiene rubber. Light-emitting-diode chips are attached to the conductive, flexible adhesive pattern on a poly(ethylene terephthalate) substrate as a visual demonstration. The brightness is invariant during bending tests.
Phase-change materials (PCMs) have received considerable attention to take advantage of both pad-type and grease-type thermal interface materials (TIMs). However, the critical drawbacks of leaking, non-recyclability, and low thermal conductivity (κ) hinder industrial applications of PCM TIMs. Here, leakage-free healable PCM TIMs with extraordinarily high κ and low total thermal resistance (R<sub>t</sub> ) are reported. The matrix material (OP) is synthesized by covalently functionalizing octadec
The low electrical conductivity of spiro-OMeTAD hole transport layers impedes further enhancements of the power conversion efficiency (PCE) of perovskite solar cells. We embedded multiwalled carbon nanotubes (MWNTs) in spiro-OMeTAD (spiro-OMeTAD/MWNTs) to increase carrier mobility and conductivity. However, direct electrical contact between CH3 NH3 PbI3 and the MWNTs created pathways for undesirable back-electron transfer, owing to the large work function of MWNTs, limiting enhancements of the P
The effect of sidewall functionalization on the dielectrophoretic mobility of single-walled carbon nanotubes is investigated using a 10-μm electrode gap and an alternating current electric field of 10 V and 10 Mhz. For nanotubes dispersed in aqueous solution using 1% sodium dodecyl sulfate, a high degree of alignment is observed for material deposited across the gap. Raman spectroscopy at 632.8- and 785-nm excitation indicates that both metallic and semiconducting nanotubes are deposited. An app
A novel silver/polymer composite with electrical conductivity (2.5 × 105 S cm−1) higher than that of bulk tungsten was developed through the addition of a small amount of multi-walled carbon nanotubes decorated with glutaric acid functionalized nano-silver particles (1.5 wt%). The nanotubes were used as one-dimensional conductive scaffolds constructing an effective electrical network among micron-sized silver powders.
A difference in work function plays a key role in charge transfer between two materials. Inorganic electrides provide a unique opportunity for electron transfer since interstitial anionic electrons result in a very low work function of 2.4-2.6 eV. Here we investigated charge transfer between two different types of electrides, [Ca(2)N](+)·e(-) and [Ca(24)Al(28)O(64)](4+)·4e(-), and single-walled carbon nanotubes (SWNTs) with a work function of 4.73-5.05 eV. [Ca(2)N](+) · e(-) with open 2-dimensio
We have studied the influence of the surface roughness of copper foils on the sheet resistance of graphene sheets grown by chemical vapor deposition. The surface roughness of the copper foils was reproducibly controlled by electropolishing. We have found that the graphene sheet resistance monotonically decreases as the surface roughness of the copper foils decreases. We show that a pre-annealing treatment combined with an optimized electropolishing process of the Cu foils and a fast CVD growth p
We investigated WS2–multiwalled carbon nanotube composites prepared by powder metallurgy. The inclusion of a small amount of nanotubes (0.75 wt%) dramatically increased electrical conductivity (by 12 300%) with a moderate decrease in the Seebeck coefficient (by 22%) and thermal conductivity (by 43%) enhancing both power factor and thermoelectric figure of merit at 300 K.
Open papers in the app to read, cite, and organize with AI.
