여운성 교수

This review paper describes several recent modification methods for biocompatible titanium dental implant surfaces. The micro-roughened surfaces reviewed in the literature are sandblasted, large-grit, acid-etched, and anodically oxidized. These globally-used surfaces have been clinically investigated, showing survival rates higher than 95%. In the past, dental clinicians believed that eukaryotic cells for osteogenesis did not recognize the changes of the nanostructures of dental implant surfaces

Electrospinning of collagen (COL)/silk fibroin (SF) blend solutions in 1,1,1,3,3,3-hexafluoro-2-propanol was investigated for fabrication of a biocompatible and biomimetic nanostructured scaffold for tissue engineering. The morphology of the electrospun COL/SF blend nanofibers was observed by scanning electron microscopy. The average diameters of COL/SF blend fibers ranged from 320 to 360 nm, irrespective of SF content in the blends. Both COL and SF components in the as-spun COL/SF blend matrice

The microbiota that forms on implant surfaces placed in the human body can be highly resistant to antimicrobial agents and in some cases cause life-threatening infections. Consequently, to limit bacterial attachment to these surfaces and thereby minimize the risk of implant infection, the process of biofilm formation and bacterial attachment must be well-understood. The oral environment is considered to be an excellent model for research into biofilm formation and implant infection, accounting f

Anatomically, the human tooth has structures both embedded within and forming part of the exterior surface of the human body. When a tooth is lost, it is often replaced by a dental implant, to facilitate the chewing of food and for esthetic purposes. For successful substitution of the lost tooth, hard tissue should be integrated into the implant surface. The microtopography and chemistry of the implant surface have been explored with the aim of enhancing osseointegration. Additionally, clinical

Screw-shaped endosseous implants that have a turned surface of commercially pure titanium have a disadvantage of requiring a long time for osseointegration while those implants have shown long-term clinical success in single and multiple restorations. Titanium implant surfaces have been modified in various ways to improve biocompatibility and accelerate osseointegration, which results in a shorter edentulous period for a patient. This article reviewed some important modified titanium surfaces, e

The aim of this study was to investigate the early bone response to the titanium dental implants with different surface characteristics using the rabbit tibia model. Calcium metaphosphate coated, anodic oxidized, hydroxyapatite particle-blasted, and turned (control) surfaces were compared. Surface topography was evaluated by field emission scanning electron microscope and optical interferometer. Eighteen rabbits received 72 implants in the tibia. Resonance frequency was analyzed every week for 6

The stability of peri-implant tissue is essential for the long-term success of dental implants. Although various types of implant connections are used, little is known about the effects of the physical mechanisms of dental implants on the stability of peri-implant tissue. This review summarizes the relevant literature to establish guidelines regarding the effects of connection type between abutments and implants in soft and hard tissues. Soft tissue seals can affect soft tissue around implants.

Ultraviolet (UV) photofunctionalization has been suggested as an effective method to enhance the osseointegration of titanium surface. In this study, machined surface treated with UV light (M + UV) was compared to sandblasted, large-grit, acid-etched (SLA) surface through in vitro and in vivo studies. Groups of titanium specimens were defined as machined (M), SLA, and M + UV for the disc type, and M + UV and SLA for the implant. The discs and implants were assessed using scanning electron micros

Abutment screw length had no significant effect on screw loosening under thermal stress. From the results of this study, daily temperature changes in the oral cavity may have no negative influence on the integrity of an implant-abutment joint when a minimum of three and a half threads of an abutment screw are engaged.

The interface between a dental implant and an abutment is stabilized by two mechanical characteristics: a preload of an abutment screw and the friction between the contact surfaces of the implant and the abutment. These mechanical properties are quantitatively analyzed by using physical and mechanical formulas. The important thing is that such mechanical properties cause various biological phenomena when medical devices are inserted into human bodies. Some mechanical complications in dental impl

Surface characteristics are an important factor for long-term clinical success of dental implants. Alterations of implant surface characteristics accelerate or improve osseointegration by interacting with the physiology of bone healing. Dental implant surfaces have been traditionally modified at the microlevel. Recently, researchers have actively investigated nano-modifications in dental implants. This review explores implant surface modifications that enhance biological response at the interfac

From the results of this in vivo study using surgically created defects, L-PRF plays an effective role as a barrier membrane for lateral ridge augmentation. L-PRF may be an excellent barrier membrane in place of other nonresorbable and resorbable membranes.

This study investigated the influences of acidity, ethanol, and pigment on the optical properties, microhardness, and surface roughness (R_a) of a nanohybrid dental composite resin. A total of 108 disc-shaped specimens were fabricated using a nanohybrid dental composite and allocated into 36 different storage solutions according to the levels of pH (2.0, 3.0, 4.0, and 5.5), ethanol (0%, 20%, and 40%), and anthocyanin pigment (0%, 2.5%, and 12.5%). Measurements of the colorimetric param