Nobuhiro Yoda

In the last few years, artificial intelligence (AI) research has been rapidly developing and emerging in the field of dental and maxillofacial radiology. Dental radiography, which is commonly used in daily practices, provides an incredibly rich resource for AI development and attracted many researchers to develop its application for various purposes. This study reviewed the applicability of AI for dental radiography from the current studies. Online searches on PubMed and IEEE Xplore databases, u

Whilst the newly established biomechanical conditions following mandibular reconstruction using fibula free flap can be a critical determinant for achieving favorable bone union, little has been known about their association in a time-dependent fashion. This study evaluated the bone healing/remodeling activity in reconstructed mandible and its influence on jaw biomechanics using CT data, and further quantified their correlation with mechanobiological responses through an in-silico approach. A 66

This experimental study provided quantitative data regarding the effect of implant location on load distribution with ISRPDs. Further investigation regarding the effect of denture design on the load distribution is needed for determining the proper implant location of ISRPD.

This study revealed that the initial BBT can significantly affect mechanobiological responses, which consequentially determines the bone remodeling process. A sufficient initial BBT is considered essential to assure a long-term stability of implant treatment.

The FEA demonstrated that as peri-implant bone loss increased, the magnitude of stress in the implant increased, especially in small diameter implants.

This study aimed to investigate the effect of attachment type on the load transmitted to implants and the residual ridge in a mandibular two-implant-supported overdenture in a model study. Ball attachments, locator attachments, and round-bar attachments were selected and examined. Static and dynamic vertical loads of 100 N were applied in the right first molar region. The load on the implants was measured by piezoelectric three-dimensional force transducers, and the load on the residual ridge be

Implant-supported fixed partial denture with cantilever extension can transfer the excessive load to the bone around implants and stress/strain concentration potentially leading to bone resorption. This study investigated the effects of implant configurations supporting three-unit fixed partial denture (FPD) on the stress and strain distribution in the peri-implant bone by combining clinically measured time-dependent loading data and finite element (FE) analysis. A 3-dimensional mandibular model

The implant location in implant-assisted removable partial dentures can affect load distribution to the supporting elements, such as the abutment tooth, implant, and mucosa under the denture base.

The purpose of this in vivo study was to evaluate the biomechanical effects of splinting of implant-supported superstructures using piezoelectric transducers to measure the three-dimensional forces exerted on implants supporting fixed superstructures. Measuring devices were set into the implant fixtures at the mandibular right second premolar and first molar. During clenching, force magnitudes were allocated more evenly to the two implants if they were splinted compared with the unsplinted contr

This study aimed to evaluate the effect of the configuration of implants supporting a four-unit fixed partial denture on load distribution. An epoxy resin model missing teeth from the first premolar to the second molar was used. Three-dimensional piezoelectric force transducers were set on implants placed in the missing teeth area with a four-unit experimental superstructure. Three-dimensional loads on the implants were measured with four different implant configurations when a static load of 10

The purpose of this study was to investigate the effect of gas species used for low-temperature atmospheric pressure plasma surface treatment, using various gas species and different treatment times, on zirconia surface state and the bond strength between zirconia and dental resin cement. Three groups of zirconia specimens with different surface treatments were prepared as follows: untreated group, alumina sandblasting treatment group, and plasma treatment group. Nitrogen (N₂), carbon

The aims of this study were to measure the three-dimensional (3-D) loads exerted on the implants supporting an overdenture during function in vivo and to clarify the effect of the number of the implants on the loads. The load-measuring devices were mounted on the implants inserted in the mandible of a 62 aged female subject. Either two or four implants connected with a bar were used for supporting her overdenture. The loads on the implants were expressed three dimensionally as load vectors and w

DTI fibre tractography confirmed regional differences in the orientation change of the masseter muscle fibres between different mandibular positions. The results may support the existence of functional partitioning inside the masseter muscle and suggest that DTI may be useful for the evaluation of muscle fibres in multipennate muscles.

Optical coherence tomography (OCT) has been emerging in the dental field as an alternative diagnostic imaging for “optical probes” owing to its micro-meter resolution and non-invasiveness. This review aims to answer the following question: what is the imaging capability of OCT to visualize the subgingival area? Online searches were performed on PubMed and SPIE digital library databases, followed by a manual screening of references listed in relevant studies. The feasibility and imaging performan

Most reports on duplicate dentures are introduction to fabrication methods or clinical case reports. Only a few studies have verified their clinical effectiveness; hence, evidence to construct useful clinical guidelines for duplicate denture use is lacking. This review aimed to comprehensively investigate reports on duplicate dentures to accumulate evidences that will contribute to the formulation of clinical practice guidelines. Duplicate dentures are effectively used for impression making and