이준석 교수

Abstract Atactic poly(vinyl alcohols) (a‐PVAs) having number‐average degrees of polymerization [( P n )s] of 1700 and 4000 were prepared by the solution polymerization of vinyl acetate, which was followed by the saponification of poly(vinyl acetate) to investigate the effects of molecular weights of a‐PVA on the characteristics of electrospun a‐PVA nanofabrics. A‐PVA nanofabrics were prepared by electrospinning with controlling the process parameters including the electrical field, conductivity,

This paper presents a salient analog phase-locked loop (PLL) that adaptively controls the loop bandwidth according to the locking status and the phase error amount. When the phase error is large, such as in the locking mode, the PLL increases the loop bandwidth and achieves fast locking. On the other hand, when the phase error is small, this PLL decreases the loop bandwidth and minimizes output jitters. Based on an analog recursive bandwidth control algorithm, the PLL achieves the phase and freq

Abstract To understand the radiative impact of tropical thin cirrus clouds, the frequency of occurrence and optical depths of these clouds have been derived. “Thin” cirrus clouds are defined here as being those that are not detected by the operational Moderate Resolution Imaging Spectroradiometer (MODIS) cloud mask, corresponding to an optical depth value of approximately 0.3 or smaller, but that are detectable in terms of the cirrus reflectance product based on the MODIS 1.375-μm channel. With

Glass fiber reinforced polyvinylchloride (PVC) composite is used widely because of its low price, chemical resistance, and dimensional stability, but most are short fiber reinforced PVC composites. Fabric reinforced composite have undulated regions, which is the only region without fiber, due to the characteristics of the weave construction, and it limits increasing the mechanical properties. Therefore, in this study, to increase the mechanical properties, the undulated regions of the glass fibe

Polyethylene based carbon fibers were studied using high density polyethylene(HDPE) fibers and linear low density polyethylene(LLDPE) fibers with various melt flow index. The draw ratio of the polyethylene fibers and the sulfonation mechanism were investigated under hydrostatic pressures of 1 and 5 bar in the first time. The influence of the melt flow index of polyethylene and types of polyethylene fibers on the sulfonation reaction was studied. Carbon fibers were prepared through the sulfonatio

In this study, the mechanical properties and thermal properties of ultra-high molecular weight polyethylene (UHMWPE)/multi wall carbon nanotubes (MWCNT) composite fiber were investigated with different weight percent of the MWCNT contents and draw ratio. To verified the thermal properties of the MWCNT/UHMWPE composite fiber, DSC and TGA analysis were performed. The addition of MWCNT and the higher draw ratio improved the thermal properties of the UHMWPE composite fiber by improving the crystalli

Carbon fibre-reinforced polymer (CFRP) composites are used in various engineering fields with their excellent mechanical properties and lightweight. However, thermoset epoxy composites with brittle epoxy resin system are leading low fracture toughness that caused deterioration during cyclic loading. In addition, the delamination occurred on the thermoset laminated composite material to impact. In this study, to improve these problems, thermoplastic resin added on the top and bottom of thermoset

PVC coated fabric is a useful structural material mainly used as a roof material because of its lightweight, flexibility. However, the main issues of this PVC coated fabric product is that it is damaged such as tensile failure, peel, and tear when exposed to extreme environments such as strong rain and wind owing to its inferior mechanical properties. Various studies have been reported to improve the mechanical properties of PVC coated fabric, there have been no significant improvement. Therefor

In this study, carbon/epoxy composites were manufactured by coating with a polyamide at different weight percentages (5 wt.%, 10 wt.%, 15 wt.%, and 20 wt.%) to improve their impact resistance and fracture toughness. The chemical reaction between the polyamide and epoxy resin were examined by fourier transform infrared spectroscopy, differential scanning calorimetry and X-ray photoelectron spectroscopy. The mechanical properties and fracture toughness of the carbon/epoxy composites were analyzed.