노준홍 교수

The band gap of formamidinium lead iodide (FAPbI3) perovskites allows broader absorption of the solar spectrum relative to conventional methylammonium lead iodide (MAPbI3). Because the optoelectronic properties of perovskite films are closely related to film quality, deposition of dense and uniform films is crucial for fabricating high-performance perovskite solar cells (PSCs). We report an approach for depositing high-quality FAPbI3 films, involving FAPbI3 crystallization by the direct intramol

The formation of a dense and uniform thin layer on the substrates is crucial for the fabrication of high-performance perovskite solar cells (PSCs) containing formamidinium with multiple cations and mixed halide anions. The concentration of defect states, which reduce a cell's performance by decreasing the open-circuit voltage and short-circuit current density, needs to be as low as possible. We show that the introduction of additional iodide ions into the organic cation solution, which are used

Chemically tuned inorganic-organic hybrid materials, based on CH3NH3(═MA)Pb(I(1-x)Br(x))3 perovskites, have been studied using UV-vis absorption and X-ray diffraction patterns and applied to nanostructured solar cells. The band gap engineering brought about by the chemical management of MAPb(I(1-x)Br(x))3 perovskites can be controllably tuned to cover almost the entire visible spectrum, enabling the realization of colorful solar cells. We demonstrate highly efficient solar cells exhibiting 12.3%

Transporter layers for greater stability Although perovskite solar cells (PSCs) can have power conversion efficiencies exceeding 20%, they can have limited stability under ultraviolet irradiation. This is in part because the mesoporous TiO 2 used as an electron-transporting layer can photocatalyze unwanted reactions in the perovskite layer. Shin et al. report a low-temperature colloidal method for depositing La-doped BaSnO 3 films as a replacement for TiO 2 to reduce such ultraviolet-induced dam

For using 2,2′,7,7′-tetrakis(N,N′-di-p-methoxyphenylamine)-9,9′-spirobifluorene (spiro-OMeTAD) as a hole conductor in solar cells, it is necessary to improve its charge-transport properties through electrochemical doping. With the aim of fabricating efficient mesoscopic TiO2/CH3NH3PbI3 heterojunction solar cells, we used tris[2-(1H-pyrazol-1-yl)-4-tert-butylpyridine)cobalt(III) tris(bis(trifluoromethylsulfonyl) imide)] (FK209) as a p-dopant for spiro-OMeTAD. The mixture of spiro-OMeTAD, FK209, l

Halide perovskite solar cells (PSCs) have recently shown a leap forward in performance by reducing the recombination loss at the interface between the perovskite and hole-transporting layers through surface treatment.

Low-temperature-processed perovskite solar cells (PSCs), especially those fabricated on flexible substrates, exhibit device performance that is worse than that of high-temperature-processed PSCs. One of the main reasons for the inferior performance of low-temperature-processed PSCs is the loss of photogenerated electrons in the electron collection layer (ECL) or related interfaces, i.e., indium tin oxide/ECL and ECL/perovskite. Here, we report that tailoring of the energy level and electron tran

In this study, we present a thermally stable multilayered transparent conducting oxide (TCO) functionalized for dye-sensitized solar cells (DSSCs). Nb-doped TiO 2 (NTO) layers deposited on conventional Sn-doped In 2 O 3 (ITO) substrates using pulsed laser deposition (PLD) enhanced the optical-to-electrical conversion efficiency of the DSSCs by as much as 17% compared to that of bare ITO-based DSSCs. The electrical properties and J − V characteristics of the multilayered NTO/ITO films showed that

Metal halide perovskite (MHP)-based tandem solar cells are a promising candidate for use in cost-effective and high-performance solar cells that can compete with fossil fuels. To understand the research trends for MHP-based tandem solar cells, a general introduction to single-junction and multiple-junction MHP solar cells and the configuration of tandem devices is provided, along with an overview of the recent progress regarding various MHP-based tandem cells, including MHP/crystalline silicon,

A highly-durable, highly-flexible transparent electrode (FTE) is developed by applying a composite made of a thin metal grid and a doped conducting polymer onto a colorless polyimide-coated NOA63 substrate. The proposed FTE exhibits a transparency of 90.7% at 550 nm including the substrate and a sheet resistance of 30.3 Ω/sq and can withstand both moderately high-temperature annealing (∼180 °C) and acidic solution (70 °C, pH 0.3) processes without performance degradation. The fabricated FTE yiel

Abstract Inorganic CsPbI 2 Br perovskite has a substantial potential for triple‐junction tandem solar cells as a top subcell, however it exhibits relative instability in the air compared with organic‐inorganic perovskites as well as significantly lower efficiency than the theoretical efficiency limit. To further enhance the air‐stability and efficiency of CsPbI 2 Br‐based perovskite solar cells (PSCs), it is vitally crucial to improve the crystallinity and passivate the defects within films that