정우빈 교수

In this work, we demonstrate that gas adsorption is significantly higher in edge sites of vertically aligned MoS2 compared to that of the conventional basal plane exposed MoS2 films. To compare the effect of the alignment of MoS2 on the gas adsorption properties, we synthesized three distinct MoS2 films with different alignment directions ((1) horizontally aligned MoS2 (basal plane exposed), (2) mixture of horizontally aligned MoS2 and vertically aligned layers (basal and edge exposed), and (3)

The development of a simple and cost-effective method for fabricating ≈10 nm scale nanopatterns over large areas is an important issue, owing to the performance enhancement such patterning brings to various applications including sensors, semiconductors, and flexible transparent electrodes. Although nanoimprinting, extreme ultraviolet, electron beams, and scanning probe litho-graphy are candidates for developing such nanopatterns, they are limited to complicated procedures with low throughput an

BACKGROUND: The purpose of this study was to evaluate the role of medial support and clinical factors responsible on outcomes and major complications associated with treatment of unstable proximal humerus fractures using a locking plate and suture augmentation. METHODS: Sixty-three cases in 62 patients (42 female, 20 male) were evaluated between September 2004 and October 2008. Cases were divided into either a medial support group (36 cases) or non-medial support group (27 cases). Clinical and r

Abstract Although the electroconversion of carbon dioxide (CO 2 ) into ethanol is considered to be one of the most promising ways of using CO 2 , the ethanol selectivity is less than 50% because of difficulties in designing an optimal catalyst that arise from the complicated pathways for the electroreduction of CO 2 to ethanol. Several approaches including the fabrication of oxide‐derived structures, atomic surface control, and the Cu + /Cu interfaces have been primarily used to produce ethanol

Achieving high electrochemical conversion of carbon dioxide (CO2) into valuable fuels and chemicals is one of the most promising directions to address environmental and energy challenges. Although several single-crystal based studies and simulation results have reported that rich in steps on Cu (100) surfaces are favorable to convert toward C2 alcohol products, most studies are still stuck in low-index (100) facets or surface defect-derived low density of step-sites. In the present work, we repo

reduction reaction showing selectivity to ethylene of ~49% and high stability for over 30 hours of reaction. Our cellulose-derived CTS method enables the greater availability of polyelemental NPs for a wide range of catalytic and electrochemical applications.

The development of highly efficient catalysts in the cathodes of rechargeable Li-O₂ batteries is a considerable challenge. Polyelemental catalysts consisting of two or more kinds of hybridized catalysts are particularly interesting because the combination of the electrochemical properties of each catalyst component can significantly facilitate oxygen evolution and oxygen reduction reactions. Despite the recent advances that have been made in this field, the number of elements in the c

Abstract The development of complex nanostructures containing a homo‐ and heteromixture of two or more metals is a considerable challenge in nanotechnology. However, previous approaches are considerably limited to the number of combinations of metals depending on the compatibility of elements, and to the complex shape control of the nanostructure. In this study, a significant step is taken toward resolving these limitations via the utilization of a low‐energy argon‐ion bombardment. The multilaye

One of the most interesting topics in physical science and materials science is the creation of complex wrinkled structures on thin-film surfaces because of their several advantages of high surface area, localized strain, and stress tolerance. In this study, a significant step was taken toward solving limitations imposed by the fabrication of previous artificial wrinkles. A universal method for preparing hierarchical three-dimensional wrinkle structures of thin films on a multiple scale (e.g., n

Abstract Design of bifunctional multimetallic alloy catalysts, which are one of the most promising candidates for water splitting, is a significant issue for the efficient production of renewable energy. Owing to large dimensions of the components and composition of multimetallic alloys, as well as the trade‐off behavior in terms of the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) overpotentials for bifunctional catalysts, it is difficult to search for high‐performance b

Transition metal dichalcogenides (TMDs) are emerging two-dimensional materials with potential use for the hydrogen evolution reaction (HER) because they express a desired binding energy with protons. To date, TMD-based HER catalytic performance has been enhanced mostly by chemical modification, such as introducing defects, doping, and phase control. Herein, we enhanced the HER performance by precise control of wettability via hierarchical wrinkling. This hierarchical wrinkling confers tunability

pH controls a large repertoire of chemical and biochemical processes in water. Densely arrayed pH microenvironments would parallelize these processes, enabling their high-throughput studies and applications. However, pH localization, let alone its arrayed realization, remains challenging because of fast diffusion of protons in water. Here, we demonstrate arrayed localizations of picoliter-scale aqueous acids, using a 256-electrochemical cell array defined on and operated by a complementary metal

The optimal architecture of three-dimensional (3D) interface between a polymer electrolyte membrane (PEM) and catalyst layer (CL) is one of the most important issues to improve PEM fuel cells' (PEMFCs) performance. Here, we report the fabrication of hierarchical wrinkled PEM/CL interface over a large area. We fabricated the hierarchical wrinkles on a multiscale from nanometers to micrometers by bottom-up-based facile, scalable, and simple method. Notably, it allows one to go beyond the limit of

Despite the extremely high energy density of the lithium metal, dendritic lithium growth caused by nonuniform lithium deposition can result in low Coulombic efficiency and safety hazards, thereby inhibiting its practical applications. Here, we report a new strategy for adopting a nanopatterned gold (Au) seed on a copper current collector for uniform lithium deposition. We find that Au nanopatterns enhance lithium metal battery performance, which is strongly affected by the feature dimensions of